Abstract. This paper provides the results of the study of a spatial flow in a low-flow stage of a SVD-22 centrifugal compressor of computational fluid dynamics methods using the Ansys CFX 14.0 software package. Low flow stages are used as the last stages of multistage centrifugal compressors. Such multistage compressors are widely used in boosting compressor stations for natural gas, in chemical industries. The flow features  in low-flow stages require independent research. This is due to the fact that the developed techniques for designing centrifugal compressor stages are created for medium-flow and high-flow stages and do not apply to low-flow stages. Generally at manufacturing new centrifugal compressors, it is impossible to make a control measurement of the parameters of the working process inside the flow path elements. Computational fluid dynamics methods are widely used to overcome this difficulties. However verification and validation of CFD methods are necessary for accurate modeling of the workflow. All calculations were conducted on one of the SPbPU clusters. Parameters of one cluster node: AMD Opteron 280 — 2 cores, 8GB RAM. The calculations were conducted using 4 nodes (HP MPI Distributed Parallel startup type) with their full load by parallelizing processes on each node.

Abstract. This paper presents the results of the study of the spatial flow in the turbocompressors elements of computational fluid dynamics methods using the Ansys CFX software package on a multiprocessor computer system. Five objects of research are considered: 1) flow path of an intermediate stage of an average-flow centrifugal compressor; 2) flow path of the low-flow centrifugal compressor stage; 3) a natural gas centrifugal compressor stage; 4) vaned diffuser of the first stage of an industrial multistage centrifugal compressor; 5) adjustable inlet stator of the first stage of an industrial turbocompressors. Generally at manufacturing new centrifugal compressors, it is impossible to make a control measurement of the parameters of the working process inside the flow path elements. Computational fluid dynamics methods are widely used to overcome this difficulties. However verification and validation of CFD methods are necessary for accurate modeling of the workflow. All calculations were performed on one of the SPbPU clusters. Parameters of one cluster: AMD Opteron 280 — 4 cores. The calculations were carried out with parallel running of the processors: HP MPI Distributed Parallel and HP MPI Local Parallel for different objects.

In this paper, we review the problem of accounting for heat exchange between the flow and the flow part surfaces when creating a calculation model for modeling the workflow process of low-flow stages of a centrifugal compressor using computational fluid dynamics (CFD). The objective selected for this study was a low-flow intermediate type stage with the conditional flow coefficient Փ = 0.008 and the relative width at the impeller exit b₂/D₂ = 0.0133. We show that, in the case of modeling with widespread adiabatic wall simplification, the calculated temperature in the gaps between the impeller and the stator elements is significantly overestimated. Modeling of the working process in the flow part was carried out with a coupled heat exchanger, as well as with simplified accounting for heat transfer by setting the temperatures of the walls. The gas-dynamic characteristics of the stage were compared with the experimental data, the heat transfer influence on the disks friction coefficient was estimated, and the temperature distributions in the gaps between disks and in the flow part of the stage were analyzed. It is shown that the main principle when modeling the flow in low-flow stage is to ensure correct temperature distribution in the gaps.

Abstract. In the course of the work, the results of estimating the error in the numerical calculation of two-element 3D impeller stages of centrifugal compressors were obtained. Gas dynamic characteristics of 6 computational models of two-element stages of a centrifugal compressor are simulated. Based on available experimental data, models of validation characteristics have been performed. A parametric model has been developed for carrying out multi-criteria and multi-parametric studies.

Abstract. To carry out research, a complex of gas-dynamic design and profiling of a two-stage centrifugal compressor with an axial-radial impeller has been developed. It is a continuous process of solving the inverse and direct problem of gas-dynamic design, profiling the flow section with subsequent analysis of the rational velocity distribution of an inviscid flow on the impeller blades on axisymmetric streamline surfaces.